Squeeg's Kustoms Quart of Epoxy Reducer QRDCR

Description

Squeeg's Kustoms / Squeeg's Hot Rod Connection
Epoxy Reducer
DIRECTIONS: For Primer, the reducer is not necessary. However, the finish will be smoother when reducer is used on final coats to allow for easier wet sanding. Follow mixing instructions thoroughly on Part A & Part B of Squeeg's Kustoms Epoxy Primer Filler Kit components before adding reducer. Then add 10% (or more if needed) reduction to Pre- mixed Part A & Part B Epoxy primer for a smoother gun finish.  Reducer can be added before or after the induction period. For Squeeg's Kustoms Epoxy Top Coat Kits use equal parts Epoxy, Catalyst and Reducer.
CAUTION!
Vapors Harmful & Extremely Flammable
A properly fitted NIOSH/MSHA approved respirator for protection against solvents and spray mists is required.
Avoid breathing vapors and spray mists. If you have chronic lung or breathing problems, do not use. Avoid contact with skin or eyes. Do not take internally. Harmful or fatal if swallowed. Do not use on objects used by children. Keep away from heat, sparks, and open flames. Vapors may cause flash fire. After using, close container immediately. Keep cap or cover tight and container upright. Contains: Ketones, Alcohols, and Aromatic solvents. The manufacturer has no control over preparation or application, therefore there is no warranty expressed or implied
KEEP OUT OF REACH OF CHILDREN
NOTICE: Not legal for sale or use in CA, CT, DE, IL, IN, MA, MD, ME, NH, NJ, NY, OH, PA, RI, VA or VT. We cannot, under any circumstances, ship to these states.
ANY AND ALL ORDERS PLACED FROM ANY OF THESE STATES CAN NOT BE SHIPPED AND THE ORDER WILL BE CANCELLED. MUST BE SHIPPED VIA GROUND. CAN ONLY BE SHIPPED WITHIN THE CONTINENTAL UNITED STATES.
All of our products are proudly
100% made in the U.S.A.
Our products are original designs meant to fill a void in the market, not just a copy of something already being offered. We have been using these parts for years in the shop on the cars we drive and build at Squeeg’s Kustoms.
Look for our other parts in our eBay store.
Also available from Squeeg’s Hot Rod Connection
Aluminum Ferrules:
A unique alternative to simply using a rubber grommet when routing lines, cables, wires, etc. through any panel. Deep enough to run through frame rails or can be used on thin sheet metal panels. 5 sizes available.
Bulkheads:
Currently 5 items consisting of an aluminum bolt-on brake line bulkhead and 4 steel weld-in frame bulkheads to run lines or wiring through your frame. Weld in bulkheads available with a plain removable plate or with two terminals perfect for running wiring from your battery to your starter.
Epoxy Primer Filler Kits and Epoxy Top Coat Kits:
Looking for the good stuff you used to use? Our legendary Epoxy Primer is still available! The same stuff we’ve been using in the shop for decades is still available.
Exhaust Tips:
Beautiful brushed stainless steel exhaust tips flared at the ends designed to be welded on. Available for 2”, 2-1/2” & 3” exhaust.
Line Separators:
Black anodized aluminum line separators for Fuel Line, Oil Line, Heater Line & A/C Line – including the new EZ-Clip A/C Line. Separators for two, three or four lines available in all popular configurations. An innovative design where the lines simply clip in to make installation and future servicing a snap with no fiddly hardware to lose. Currently, there are 16 parts in the A/C & Heater category and 34 for Fuel and Oil lines. Matching Plug Wire Separators also available.
Pewter Key Chains:
Based on original artwork by Jimmy Smith of cars built by Squeeg’s Kustoms. 6 designs available; 32 Ford Coupe, 33 Ford Roadster, 34 Ford Coupe, 36 Ford Coupe, 40 Ford Coupe, and 50 Merc Custom.
Plug Wire Separators:
Black anodized aluminum separators for plug wires. Just like our Line Separators, the wires simply clip in to make installation and future servicing a snap with no fiddly hardware to lose.  Offered in 8mm and 8.5mm. There are 6 kits for Big Block Chevy, Small Block Chevy, and Small Block Ford. Also available are the individual components so customers can build their own kits. The wire mounts are sold two per pack and the floating separators four per kit. There are 14 different components available.
Steering Wheels, Adapters & Spacer:
Cast aluminum drilled I Beam style perfect for early hot rods. Available as cast or polished and wrapped or unwrapped. 4 configurations currently offered. Two column adapters available: early Ford (1928-48) keyed columns and GM splined columns as well as an Aluminum ½” spacer.
T-Shirts:
10 Styles available featuring artwork by Jimmy Smith. Each style is available in either Black or White in Sizes from Small through 3XL. Many clearance shirts are available in various colors as well as Women’s shirts.
Wheels:
Early Sprint Car style classic aluminum wheels. Available in Starburst for Ford spindle mount 15” x 4.5”, Sprint in sizes from 15” x 4.5” through 16” x 10”, and Champs in sizes from 16” x 11” through 16” x 13”. All wheels are made to order. Standard available bolt patterns 5 on 4 ½”, 5 on 4 ¾” and 5 on 5 ½”. Other bolt patterns are available, contact us for more information.
Wheel Center Caps:
Cast aluminum caps designed to match cast wheels. Originally designed for American Rebel wheels, but suitable for many other wheels. Made in flat or with a domed center. Available as cast or polished in 5 on 4 ½”, 5 on 4 ¾” and 5 on 5 ½” bolt patterns.